Tomos Riders Forum
Ostale teme vezane uz motore => Ostala vozila => Autor teme: BT80 - Ožujak 18, 2015, 22:40:20
-
Evo teme o mom kabrioletu :mrgreen:
Kopirana sa fica foruma :biggrin:
BT80 - 26-5-2014 u 22:45
Evo rijesio sam da predtsavim i svog Ficu 850 :D
Ovo su malo starije slike al nema veze(trenutno je na klocnama ceka sredjivanje)
(http://s19.postimg.org/8aaq00z7z/087.jpg)
(http://s19.postimg.org/6rfbv1snj/26_12_11_2.jpg)
(http://s19.postimg.org/faypst0zz/26_12_11_1.jpg)
(http://s19.postimg.org/l0eyd4767/168.jpg)
mikicak - 27-5-2014 u 08:42
-na osnovu ovih fotografija dobar mada bih ja skinuo ovu plavu lajsnu na prednjem veznom limu mislim da bi bio lepsi bez nje :ok::deda:
BT80 - 27-5-2014 u 18:20
Ima oko njega dosta posla da se dovede u red,to je stari pravio prije 20god, sad je doso red da se malo sredi :moron:hehe
BT80 - 14-6-2014 u 10:50
Nabavio sam motor od 965ccm i poceo ga sredjivat :) Prvo sam ga detaljno ocistio:)
evo par slika :)
(http://s19.postimg.org/w0z48p1e7/DSCN1273.jpg)
(http://s19.postimg.org/4rnqu70b3/DSCN1274.jpg)
Zalijepio sam smirgl papir za plocicu i ocistio malo blok gdje nalijeze glava, e sad pitanje: jeli ovo dovoljno ili treba smirglati da skroz nestanu crne fleke?
(http://s19.postimg.org/cyfqlrqdr/DSCN1275.jpg)
(http://s19.postimg.org/k2xjusxn3/DSCN1276.jpg)
Zamijenjene gumice ventila i ventili uslajfani :)
(http://s19.postimg.org/ha4carxan/DSCN1277.jpg)
Kad je sve rasklopljeno, trebao bi mu i karike zamijenut ali kod nas u BiH tesko nac ove od 67.2mm.Da li ima u Srbiji da se nabave te karike?
BT80 - 16-6-2014 u 12:43
Kad bih ugradio na ovaj motor vodenu pumpu od 850 motora, da li bi imala dovoljan kapacitet i protok da hladi ovaj motor? :)
vule.abarth - 16-6-2014 u 13:21
Lep ti je Fića,Pony bicikl,krosaljka 91ccm... :plezise:
Od čega je motor?
Godište,koliko je rešao,daj malo više podataka o njemu.
BT80 - 16-6-2014 u 13:36
Ooo pa ti si sa Tomos foruma :D
Motor je mislim od Fiat Pande, neznam koje je godiste ni koliko je presao, 965ccm i 50KS, u solidnom je stanju klipovi neosteceni vide se skroz okolo crtice od obrdae.Uzeo sam ga golog bez karburatora,poklopca ventila i vodene pumpe.Vodenu pumpu sam nabavio od juga, al mislim ugradit od 850 motora, samo neznam jos hoceli imati dovoljan kapacitet i protok da ga ohladi dok mi neko ne rekne od iskusnijih :)
BT80 - 17-6-2014 u 11:01
Imam ovaj dvogrli karburator 28/32 , bi li on mogao na ovaj motor tj. da li bi bio preveliki? :)
(http://s19.postimg.org/cuv3wzznz/2014_06_17_926.jpg)
(http://s19.postimg.org/y5so19hsf/2014_06_17_928.jpg)
(http://s19.postimg.org/x4sfc50sv/2014_06_17_927.jpg)
pedjamil - 17-6-2014 u 12:17
Ja mislim da je prevelik, ali nemam iskustva sa tim motorom. Verovatno će da radi , ali će mnogo da troši i kod naglog smanjenja broja obrtaja , malo će da davi motor i da puca u izduvu.
BT80 - 17-6-2014 u 12:34
Koji bi bio dobar dvogrli za ovaj motor i od cega? :)
pedjamil - 17-6-2014 u 16:49
23/23 , ili nešto slično...Sa Fiata 850 sport i drugih sa manjim zapreminama motora, ali i drugih automobila mimo Fiat grupacije (Citroen GS 1300 na primer).
BT80 - 26-6-2014 u 21:25
Radi se pomalo oko ficka :)
Napravljeni i zavareni nosaci auspuha na karter od Fiata
(http://s19.postimg.org/her3nlpvz/2014_06_26_929.jpg)
(http://s19.postimg.org/s0ayzlw7j/2014_06_26_930.jpg)
Spremljen blok za farbanje :)
(http://s19.postimg.org/meojvjvin/2014_06_26_931.jpg)
(http://s19.postimg.org/jymqhpdfz/2014_06_26_932.jpg)
(http://s19.postimg.org/5gpj9pm4v/2014_06_26_933.jpg)
(http://s19.postimg.org/yx55c4si7/2014_06_26_934.jpg)
Dvoumim se koju da stavim pumpu desno je ficina
(http://s19.postimg.org/qipio1rgv/2014_06_26_940.jpg)
(http://s19.postimg.org/h8dekigr3/2014_06_26_936.jpg)
Desno je ficin 850 motor farban prije pola godine dok jos nisam nabavio Fiatov :)
(http://s19.postimg.org/b8pnguvyn/2014_06_26_937.jpg)
BT80 - 30-6-2014 u 13:07
Ovih dana sam se malo pozabavio oko instrument table :)
Imo sam satove od lade 2105(1200)
(http://s19.postimg.org/6tgvmgf9r/2014_06_27_945.jpg)
i lade 2107(1300)
(http://s19.postimg.org/njs9bsdov/2014_06_27_946.jpg)
Odlucio sam obrtomjer iz 2107 ubacit u kuciste od 2105(oruginal podloga od obrtomjera 2107 je veca i treba se malo smanjiti precnik)
(http://s19.postimg.org/oakzhkg27/2014_06_27_949.jpg)
Posto je obrtomjer duzi morao sam prosjec
(http://s19.postimg.org/62o5gocwf/2014_06_27_947.jpg)
Onda sam isjekao kuciste od obrtmojera gdje je prije bio i zalemio za sadasnje
(http://s19.postimg.org/t6om99g7j/2014_06_27_950.jpg)
(http://s19.postimg.org/dqb1yzbkf/2014_06_27_951.jpg)
(http://s19.postimg.org/471d5io27/2014_06_27_953.jpg)
i dodao kuciste lampice ulja
(http://s19.postimg.org/xapl1rc5r/2014_06_30_955.jpg)
Onda sam istampo bijele podloge i zalijepio
(http://s19.postimg.org/ng3199xlb/2014_06_30_954.jpg)
(http://s19.postimg.org/xc448x3db/2014_06_30_956.jpg)
A evo i ostalih satova
(http://s19.postimg.org/jc22gs1n3/2014_06_30_957.jpg)
(http://s19.postimg.org/iy0qh6hjj/2014_06_30_958.jpg)
(http://s19.postimg.org/7x5lc5pan/2014_06_30_959.jpg)
Pa ako se neko odluci pravit mozda mu pomogne hehe
X - 2-7-2014 u 09:43
Lepo izgleda, ali ne znam koliko su tacni ti satovi, znam da skazaljka obrtomera skace na naglije dodavanje gasa.
pedjamil - 2-7-2014 u 09:55
Svaka čast na strpljenju , lepo ovo izgleda :ok:
@X Za obrtomer ne znam tačno (znam da hoće da oscilira) , ali za km sat znam sa puta , jer je uporedjivano sa GPS-om; laže tačno 10 % .
BT80 - 2-7-2014 u 16:19
Hvala, trudio sam se da na nesto lici hehe
Znam da oscilira al jbg nisam imao druge :)
BT80 - 2-7-2014 u 17:05
Nabavio sam karburator Solex 34, dal ce da biti dobar za ovaj motor(965)?
Evo ovakav:
(http://s19.postimg.org/enhxr840f/vw_buba_karburator_solex_34_pict_3_slika_1531955.jpg)
aleksandarFilipovic - 2-7-2014 u 19:16
Toje Bubin karburator za 1200 kubika
BT80 - 2-7-2014 u 20:19
Nebi mu trebo biti preveliki??? :)
Edit:i vrijedi li probat na ovaj motor?? hehe
BT80 - 3-7-2014 u 20:31
Evo karburator odkuhan, ociscen i spreman za ugradnju hehe
(http://s19.postimg.org/qgkc96pu7/2014_07_03_963.jpg)
(http://s19.postimg.org/qhua2lrnz/2014_07_03_962.jpg)
(http://s19.postimg.org/tpyrfndxr/2014_07_03_964.jpg)
(http://s19.postimg.org/609bqyfkf/2014_07_03_965.jpg)
pedjamil - 3-7-2014 u 23:58
I ,kakva je bila supa ? :D
BT80 - 4-7-2014 u 00:16
Masna i zestoka hehe:plezise::D
BT80 - 5-7-2014 u 12:07
Napravljena je i prirubnica za karburator :)
(http://s19.postimg.org/97hnft45r/2014_07_04_966.jpg)
(http://s19.postimg.org/zeiubrmfj/2014_07_04_967.jpg)
(http://s19.postimg.org/k8hdyklsf/2014_07_05_970.jpg)
(http://s19.postimg.org/vyvbfyekv/2014_07_05_969.jpg)
(http://s19.postimg.org/cbsbclky7/2014_07_05_968.jpg)
samba - 5-7-2014 u 19:37
Odlicno za sad,samo polako i imaj strpljenja:ok:
BT80 - 5-7-2014 u 21:47
Hvala, trudim se :)
BT80 - 9-12-2014 u 11:50
Evo ga i mjenjac :)
Sinhroni i donji snop zupcanika stavljen je od Fiata, prva przina i rikverc ne osteceni :)
Diferencijal 8/39
(http://s19.postimg.org/97uslgpfz/2014_11_10_1097.jpg)
(http://s19.postimg.org/pk4ub73rj/2014_11_10_1098.jpg)
(http://s19.postimg.org/hso4cmzm7/2014_11_10_1096.jpg)
(http://s19.postimg.org/pmopy17f3/2014_11_10_1100.jpg)
(http://s19.postimg.org/6640bicb3/2014_11_10_1099.jpg)
(http://s19.postimg.org/cl3186j0v/2014_11_10_1102.jpg)
BT80 - 20-12-2014 u 18:05
Stigle karike i dihting glave :)
-karike 100e
-dihtung 15e
(http://s19.postimg.org/d5px3ropb/10850369_744112045672061_922040604_n.jpg)
(http://s19.postimg.org/8b0tj8frj/2014_12_20_1168.jpg)
(http://s19.postimg.org/ygnh816tr/10872177_744112192338713_624341637_n.jpg)
(http://s19.postimg.org/6hxwuwukv/2014_12_20_1167.jpg)
BT80 - 22-12-2014 u 18:27
Ubaceni klipovi i glava poravnata i skinuta za pola mm :)
(http://s19.postimg.org/3ui3vex8v/2014_12_22_1170.jpg)
(http://s19.postimg.org/odd00hb67/2014_12_22_1169.jpg)
pedjamil - 22-12-2014 u 19:36
:ok:
Milovanovic - 23-12-2014 u 18:53
Svaka cast kolega, kad si atestirao kabria,mislim da sada to kod nas nije moguce po novom zakonu
BT80 - 24-12-2014 u 14:22
Nisam ga jos atestirao, a mislim da se kod nas moze, trebam se jos raspitati kako i sta. :)
BT80 - 25-12-2014 u 09:51
Postavljena glava i klackalice i stegnuto :)
(http://s19.postimg.org/ffols4r7z/2014_12_23_1173.jpg)
(http://s19.postimg.org/om6wfewgf/2014_12_23_1174.jpg)
šale - 25-12-2014 u 14:52
Gledajući ovaj dihtung i blok motora,prostor između cilindara na bloku mnogo je veći nego na dihtungu,kao da je blok 65 a dihtung za 67,možda me oko vara.I kog je hoda radilica.
Lepo odrađeno.
(http://s19.postimg.org/d5px3ropb/10850369_744112045672061_922040604_n.jpg) (http://s19.postimg.org/3ui3vex8v/2014_12_22_1170.jpg)
BT80 - 25-12-2014 u 16:07
I blok i dihtung su 67,2mm, a hod radilice je 68mm :)
Dihtung se tacno poklapa, sam nisam slikao dok je bio na bloku :)
Hvala :)
BT80 - 27-12-2014 u 19:38
Motor se polako sastavlja :cool:
Usput koje bi ulje nasuo, viskozitet? :)
(http://s19.postimg.org/tb14z76q7/2014_12_27_1175.jpg)
(http://s19.postimg.org/a77tiutvz/2014_12_27_1176.jpg)
(http://s19.postimg.org/v1k60oo9b/2014_12_27_1177.jpg)
(http://s19.postimg.org/jvpuzqe33/2014_12_27_1178.jpg)
(http://s19.postimg.org/qjhv8l87j/2014_12_27_1179.jpg)
(http://s19.postimg.org/rztdqqb4f/2014_12_27_1180.jpg)
X - 31-12-2014 u 18:36
15-40, kao sto fabrika kaze.
Svidja mi se boja motora. :)
Da li si merio da li je blok kriv odozgo?
BT80 - 1-1-2015 u 16:41
Hvala na odgovoru :)
Nisam mjerio dal je blok kriv :undecided:
BT80 - 6-1-2015 u 06:33
Motor se sastavlja polako :)
Jos se omisljam dal da ugradjujem ficinu vodenu pumpu ili ovu od ovog motor :huh:
(http://s19.postimg.org/c3tkdzmj3/2015_01_05_1184.jpg)
(http://s19.postimg.org/4ccuffidr/2015_01_05_1185.jpg)
(http://s19.postimg.org/wqi9zb5xr/2015_01_05_1186.jpg)
X - 6-1-2015 u 19:22
Ficina ti se ne uklapa na taj motor, moraces onu originalnu.
BT80 - 7-1-2015 u 09:07
Znam da se ne uklapa, mislio sam napraviti plocicu koja odgovara i i onda skratiti ficinu koliko treba i zavariti, posto imam dobrog varioca aluminijuma :)
Marko94 - 7-1-2015 u 10:10
Možeš Fićinu da ugradiš, treba da je skratiš za debljinu ploče i da je odsečeš pod uglom jer taj blok nema nagib za pumpu kao Fićin ;) inače odličan posao, svaka čast :ok:
BT80 - 7-1-2015 u 22:52
Hvala :) tako sam mislio uraditi, malo ce biti zezanja al trebalo bi se dati :)
dserbia - 8-1-2015 u 18:54
lep posao, jel mogu da te zamolim da mi kazes koja je oznaka na bloku motora? Nisam znao da taj promer karika ide na 965 kubika!?
BT80 - 8-1-2015 u 22:56
Hvala :)
Oznaka na bloku je A112 B1. 054, da idu 67,2mm karike, fabricki :)
dserbia - 8-1-2015 u 23:07
Zbunilo me je sto gledajuci glavu motora mi se cini da je ista kao kod a112 abarth motora a i 67.2mm je dimenzija koja ide na taj motor. Naravno A112 B1. 054 je pandin motor kao sto si I napisao...
BT80 - 8-1-2015 u 23:34
Da u pandu se ugradjivao, ali oznaka mi govori da je i ovo mozda abarth samo slabiji (50KS) :)
Goran63 - 9-1-2015 u 15:11
Svaka cast,samo napred,odlican fica kabrio!
BT80 - 9-1-2015 u 21:04
Hvala :)
GIOVANNI - 10-1-2015 u 14:08
Dobar projekt, samo napred !
BT80 - 10-1-2015 u 16:58
Hvala :)
BT80 - 21-1-2015 u 19:56
Napravljeni nosaci pumpe, s kojim cu posle ucentrirati na Fiatov blok :)
(http://s19.postimg.org/dn6gmq18v/2015_01_16_1218.jpg)
(http://s19.postimg.org/jcmp717f3/2015_01_16_1217.jpg)
(http://s19.postimg.org/7osnchia7/2015_01_16_1216.jpg)
(http://s19.postimg.org/wjc56k34f/2015_01_16_1219.jpg)
(http://s19.postimg.org/3w94wr2rz/2015_01_16_1220.jpg)
Napravljen adapter(medju ploca) :)
(http://s19.postimg.org/7vbecoxqn/2015_01_17_1222.jpg)
(http://s19.postimg.org/b3fvpqk0f/2015_01_17_1224.jpg)
(http://s19.postimg.org/ogj0scoun/2015_01_17_1221.jpg)
BT80 - 22-1-2015 u 18:07
Pumpa skracena, nacentrirana i zavarena :)
(http://s19.postimg.org/4uh8aaz7z/2015_01_21_1226.jpg)
(http://s19.postimg.org/w6chbn3yn/2015_01_21_1225.jpg)
(http://s19.postimg.org/4rxcngvkf/2015_01_21_1227.jpg)
(http://s19.postimg.org/7ib9yehn3/2015_01_21_1228.jpg)
(http://s19.postimg.org/cypcf1ln3/2015_01_21_1230.jpg)
(http://s19.postimg.org/cr1pijaof/2015_01_21_1231.jpg)
(http://s19.postimg.org/l817tgfdb/2015_01_21_1233.jpg)
(http://s19.postimg.org/ty2w81m8f/2015_01_21_1236.jpg)
(http://s19.postimg.org/uovmdtolr/20150121_201643.jpg)
(http://s19.postimg.org/kg35800jz/20150121_201439.jpg)
X - 22-1-2015 u 19:07
Svaka cast! Javi kako funkcionise. :ok:
BT80 - 22-1-2015 u 21:38
Ok sve ce biti objavljeno :)
(http://s19.postimg.org/rgieso4i7/2015_01_22_1238.jpg)
Marko94 - 22-1-2015 u 22:36
Svaka čast, isti sam posao radio kod mene na 903 i nije bilo problema sa hladjenjem. Samo napred :ok:
BT80 - 22-1-2015 u 22:46
Koliko tacno litara ulja ide u ovaj motor? :)
X - 24-1-2015 u 11:05
Mislim da treba 4L ako se dobro secam. Kupi 4 pa ako ne stane sve, mozda ti ostane do 0,5L za dolivanje.
BT80 - 31-1-2015 u 20:52
Aha, hvala na odgovoru :)
Evo masinica je upalilaa :moron:
https://www.youtube.com/watch?v=m4bK50cyPoI&feature=youtu.be (https://www.youtube.com/watch?v=m4bK50cyPoI&feature=youtu.be)
Marko94 - 31-1-2015 u 23:09
Ajoj rodjače pa što nov motor u ovoliku turažu? Inače svaka čast za posao :)
BT80 - 31-1-2015 u 23:47
Nije pod opterecenjem pa da se ne smije gasirat, msm nebi trebalo ni sada al jbg :zviz:
Hvala :)
zloćko - 1-2-2015 u 07:43
samo ti njega kolji nek se zna ko mu je gazda :D
BT80 - 1-2-2015 u 11:06
e too nek se odmah navikava :D :losi-zubi:
Kad ga budem razradjivao moracu staviti sraf ispod papucice gasa da ne moze iznad 2000o/min hehe
Morao sam ga malo izgasirat za forum :)
pedjamil - 1-2-2015 u 12:56
:ok: Za blokadu koristi ciglu ispod papučice gasa , koja može poslužiti i kao tempomat na dužem putu...:D
BT80 - 1-2-2015 u 13:19
vidis toga se nisam sjetio :rock: haha
BT80 - 6-2-2015 u 10:05
Jel ovo ficina korpa novi tip? :)
(http://s19.postimg.org/5geiionnz/2015_02_05_1292.jpg)
(http://s19.postimg.org/54x25x77z/2015_02_05_1294.jpg)
(http://s19.postimg.org/6xzyu8sen/2015_02_05_1293.jpg)
pedjamil - 6-2-2015 u 12:02
Jeste
BT80 - 6-2-2015 u 17:56
Ne znam koju bi stavio dal ovu novi tip ili stari tip(pod opruge podmetnute podloske od 1.5mm), na ovaj motor...? :)
pedjamil - 7-2-2015 u 15:32
Kažu ljudi da je bolji stari tip (ja nisam probao , jer imam korpu sa jačim srcem napravljenu po porudžbini , kao i lamelu). Fićina korpa novog tipa nije najbolje držala i lamela (originalna) je proklizavala , pa sam zamenio. Doduše , nisam nimalo nežan sa kvačilom , odnosno , uopšte nisam normalan kad vozim Fiću...
Marko94 - 7-2-2015 u 16:02
Kod mene se daleko bolje pokazalo kvacilo stari tip, mada je i ona znala malo da prokliza pod veliki opterecenjem. Ja licno planiram da stavim dosta jace opruge u korpu i novi tip lamele sa kvalitetnijim oblogama, valjda ce da drzi :D
BT80 - 7-2-2015 u 23:20
Onda cu ostaviti stari tip, malo sam podlozio opruge, nebi trebala onda proklizavati... :)
X - 8-2-2015 u 13:21
Ja sam koristio sve novi tip i nisam imao problema, ali su korpa i lamela bili novi a zamajac je bio potpuno ravan (na to treba isto obratiti paznju jer druga strana lamele lezi i radi na zamajcu).
BT80 - 8-2-2015 u 14:41
Sad cu ostaviti stari tip posto sam vec namontirao pa cemo vidjet kako ce se pokazati... :)
BT80 - 15-3-2015 u 09:50
Skalapa se i 850, nabavio sam klip koji mi je hvalio :)
i slucajno u garazi nadjem bragastu uzmem pomicno mjerilo, kad ono specijalova brega (35mm bregovi):losi-zubi::huepfenred: nju cu da stavim u ovaj motor :D
Izduve sam vec ranije prosirio na 27 mm
i usis 27mm sa 57mm
Jos planiram spustiti glavu, a nezz koliko bi najbolje bilo, sta vi mislite? :D
(http://s19.postimg.org/y7f2d89jj/11063358_789211271162138_482343260_n.jpg)
(http://s19.postimg.org/iknszuvrj/11040817_789220087827923_1935024368_n.jpg)
(http://s19.postimg.org/ldh0jvw3z/11022942_789212014495397_1000275244_n.jpg)
zemunelo - 15-3-2015 u 11:12
Da li si probao ovu pumpu ovako zavarenu i namestenu na blok motora da li se dobro gadja difuzor odn. ventilator pumpe na hladnjak? Nisam siguran,ali jugov blok je vertikalno ravan na delu gde se kaci pumpa za vodu a ficin je pod malo drugacijim uglom na tom mestu pa ako si pumpu ravnao po ficinoj meri za blok moze ti se desiti da ne nailazi najbolje difuzor pumpe na hladnjak.
Sto se tice spustanja glave,mislim da bi bilo zadovoljavajuce skidati do 1mm ukupno jer se malo dobija na kompresiji,barem ja razmisljam da nekad kad budem radio drugi motor za toliko ''skinem'' glavu.
Koji je karburator na 903 motoru i zasto ficin razvodnik paljenja?
BT80 - 15-3-2015 u 11:44
Pumpa je ravnata po ovom A112 bloku(965) tj osovina propelera(pumpe)je isto udaljena od motora i po vertikali i horizontali ko u fice.Vidi se po slikama da sam nosace pravio na ficinom i to sve premjestio na a112 :)
Karburaor je vokswagenov 34
razvodnik je ficin zbog zatvaranja haube i zato sto sam taj imao...
BT80 - 18-3-2015 u 22:21
Spustena glava za 1.5mm :)
(http://s19.postimg.org/6n0zhh6j3/20150318_102835.jpg)
(http://s19.postimg.org/r8fr9do3z/20150318_102816.jpg)
Produbljeni kanali za vodu
(http://s19.postimg.org/tn7mtt4cv/20150318_111239.jpg)
i namontirana :)
(http://s19.postimg.org/q8u1reybz/20150318_171126.jpg)
(http://s19.postimg.org/l8s05q3bj/20150318_173240.jpg)
-
:palacgore:
fico mmmmm
i jesi rjesija nedoumicu oko pumpe??
neće mi poveća slike :misli:
-
ni meni....slike povecaj :palacgore:
Inače kupit cu ficu samo da ga imam fora auto :mrgreen:
-
Pumpu sam stavio ficinu, napravio adapter za A112 motor, osjekao ficin prihvat i taj adapter navario :biggrin:
Slike se ne mogu povecati zato sto sam kopirao sve, a ne znam kako ih mogu povecati :tuzan:
-
Sad bi se trebale moci slike vidjeti :biggrin:
Evo rijesio sam da predtsavim i svog Ficu 850 :D
Ovo su malo starije slike al nema veze(trenutno je na klocnama ceka sredjivanje)
(http://s19.postimg.org/8aaq00z7z/087.jpg) (http://postimg.org/image/8aaq00z7z/)
(http://s19.postimg.org/6rfbv1snj/26_12_11_2.jpg) (http://postimg.org/image/6rfbv1snj/)
(http://s19.postimg.org/faypst0zz/26_12_11_1.jpg) (http://postimg.org/image/faypst0zz/)
(http://s19.postimg.org/l0eyd4767/168.jpg) (http://postimg.org/image/l0eyd4767/)
Nabavio sam motor od 965ccm i poceo ga sredjivat :) Prvo sam ga detaljno ocistio:)
evo par slika :)
(http://s19.postimg.org/w0z48p1e7/DSCN1273.jpg) (http://postimg.org/image/w0z48p1e7/)
(http://s19.postimg.org/4rnqu70b3/DSCN1274.jpg) (http://postimg.org/image/4rnqu70b3/)
Zalijepio sam smirgl papir za plocicu i ocistio malo blok gdje nalijeze glava, e sad pitanje: jeli ovo dovoljno ili treba smirglati da skroz nestanu crne fleke?
(http://s19.postimg.org/cyfqlrqdr/DSCN1275.jpg) (http://postimg.org/image/cyfqlrqdr/)
(http://s19.postimg.org/k2xjusxn3/DSCN1276.jpg) (http://postimg.org/image/k2xjusxn3/)
Zamijenjene gumice ventila i ventili uslajfani :)
(http://s19.postimg.org/ha4carxan/DSCN1277.jpg) (http://postimg.org/image/ha4carxan/)
Kad je sve rasklopljeno, trebao bi mu i karike zamijenut ali kod nas u BiH tesko nac ove od 67.2mm.Da li ima u Srbiji da se nabave te karike?
Imam ovaj dvogrli karburator 28/32 , bi li on mogao na ovaj motor tj. da li bi bio preveliki? :)
(http://s19.postimg.org/cuv3wzznz/2014_06_17_926.jpg) (http://postimg.org/image/cuv3wzznz/)
(http://s19.postimg.org/y5so19hsf/2014_06_17_928.jpg) (http://postimg.org/image/y5so19hsf/)
(http://s19.postimg.org/x4sfc50sv/2014_06_17_927.jpg) (http://postimg.org/image/x4sfc50sv/)
Radi se pomalo oko ficka :)
Napravljeni i zavareni nosaci auspuha na karter od Fiata
(http://s19.postimg.org/her3nlpvz/2014_06_26_929.jpg) (http://postimg.org/image/her3nlpvz/)
(http://s19.postimg.org/s0ayzlw7j/2014_06_26_930.jpg) (http://postimg.org/image/s0ayzlw7j/)
Spremljen blok za farbanje :)
(http://s19.postimg.org/meojvjvin/2014_06_26_931.jpg) (http://postimg.org/image/meojvjvin/)
(http://s19.postimg.org/jymqhpdfz/2014_06_26_932.jpg) (http://postimg.org/image/jymqhpdfz/)
(http://s19.postimg.org/5gpj9pm4v/2014_06_26_933.jpg) (http://postimg.org/image/5gpj9pm4v/)
(http://s19.postimg.org/yx55c4si7/2014_06_26_934.jpg) (http://postimg.org/image/yx55c4si7/)
Dvoumim se koju da stavim pumpu desno je ficina
(http://s19.postimg.org/qipio1rgv/2014_06_26_940.jpg) (http://postimg.org/image/qipio1rgv/)
(http://s19.postimg.org/h8dekigr3/2014_06_26_936.jpg) (http://postimg.org/image/h8dekigr3/)
Desno je ficin 850 motor farban prije pola godine dok jos nisam nabavio Fiatov :)
(http://s19.postimg.org/b8pnguvyn/2014_06_26_937.jpg) (http://postimg.org/image/b8pnguvyn/)
Ovih dana sam se malo pozabavio oko instrument table :)
Imo sam satove od lade 2105(1200)
(http://s19.postimg.org/6tgvmgf9r/2014_06_27_945.jpg) (http://postimg.org/image/6tgvmgf9r/)
i lade 2107(1300)
(http://s19.postimg.org/njs9bsdov/2014_06_27_946.jpg) (http://postimg.org/image/njs9bsdov/)
Odlucio sam obrtomjer iz 2107 ubacit u kuciste od 2105(oruginal podloga od obrtomjera 2107 je veca i treba se malo smanjiti precnik)
(http://s19.postimg.org/oakzhkg27/2014_06_27_949.jpg) (http://postimg.org/image/oakzhkg27/)
Posto je obrtomjer duzi morao sam prosjec
(http://s19.postimg.org/62o5gocwf/2014_06_27_947.jpg) (http://postimg.org/image/62o5gocwf/)
Onda sam isjekao kuciste od obrtmojera gdje je prije bio i zalemio za sadasnje
(http://s19.postimg.org/t6om99g7j/2014_06_27_950.jpg) (http://postimg.org/image/t6om99g7j/)
(http://s19.postimg.org/dqb1yzbkf/2014_06_27_951.jpg) (http://postimg.org/image/dqb1yzbkf/)
(http://s19.postimg.org/471d5io27/2014_06_27_953.jpg) (http://postimg.org/image/471d5io27/)
i dodao kuciste lampice ulja
(http://s19.postimg.org/xapl1rc5r/2014_06_30_955.jpg) (http://postimg.org/image/xapl1rc5r/)
Onda sam istampo bijele podloge i zalijepio
(http://s19.postimg.org/ng3199xlb/2014_06_30_954.jpg) (http://postimg.org/image/ng3199xlb/)
(http://s19.postimg.org/xc448x3db/2014_06_30_956.jpg) (http://postimg.org/image/xc448x3db/)
A evo i ostalih satova
(http://s19.postimg.org/jc22gs1n3/2014_06_30_957.jpg) (http://postimg.org/image/jc22gs1n3/)
(http://s19.postimg.org/iy0qh6hjj/2014_06_30_958.jpg) (http://postimg.org/image/iy0qh6hjj/)
(http://s19.postimg.org/7x5lc5pan/2014_06_30_959.jpg) (http://postimg.org/image/7x5lc5pan/)
Pa ako se neko odluci pravit mozda mu pomogne hehe
Evo karburator odkuhan, ociscen i spreman za ugradnju hehe
(http://s19.postimg.org/qgkc96pu7/2014_07_03_963.jpg) (http://postimg.org/image/qgkc96pu7/)
(http://s19.postimg.org/qhua2lrnz/2014_07_03_962.jpg) (http://postimg.org/image/qhua2lrnz/)
(http://s19.postimg.org/tpyrfndxr/2014_07_03_964.jpg) (http://postimg.org/image/tpyrfndxr/)
(http://s19.postimg.org/609bqyfkf/2014_07_03_965.jpg) (http://postimg.org/image/609bqyfkf/)
Napravljena je i prirubnica za karburator :)
(http://s19.postimg.org/97hnft45r/2014_07_04_966.jpg) (http://postimg.org/image/97hnft45r/)
(http://s19.postimg.org/zeiubrmfj/2014_07_04_967.jpg) (http://postimg.org/image/zeiubrmfj/)
(http://s19.postimg.org/k8hdyklsf/2014_07_05_970.jpg) (http://postimg.org/image/k8hdyklsf/)
(http://s19.postimg.org/vyvbfyekv/2014_07_05_969.jpg) (http://postimg.org/image/vyvbfyekv/)
(http://s19.postimg.org/cbsbclky7/2014_07_05_968.jpg) (http://postimg.org/image/cbsbclky7/)
Evo ga i mjenjac :)
Sinhroni i donji snop zupcanika stavljen je od Fiata, prva przina i rikverc ne osteceni :)
Diferencijal 8/39
(http://s19.postimg.org/97uslgpfz/2014_11_10_1097.jpg) (http://postimg.org/image/97uslgpfz/)
(http://s19.postimg.org/pk4ub73rj/2014_11_10_1098.jpg) (http://postimg.org/image/pk4ub73rj/)
(http://s19.postimg.org/hso4cmzm7/2014_11_10_1096.jpg) (http://postimg.org/image/hso4cmzm7/)
(http://s19.postimg.org/pmopy17f3/2014_11_10_1100.jpg) (http://postimg.org/image/pmopy17f3/)
(http://s19.postimg.org/6640bicb3/2014_11_10_1099.jpg) (http://postimg.org/image/6640bicb3/)
(http://s19.postimg.org/cl3186j0v/2014_11_10_1102.jpg) (http://postimg.org/image/cl3186j0v/)
Stigle karike i dihting glave :)
-karike 100e
-dihtung 15e
(http://s19.postimg.org/d5px3ropb/10850369_744112045672061_922040604_n.jpg) (http://postimg.org/image/d5px3ropb/)
(http://s19.postimg.org/8b0tj8frj/2014_12_20_1168.jpg) (http://postimg.org/image/8b0tj8frj/)
(http://s19.postimg.org/ygnh816tr/10872177_744112192338713_624341637_n.jpg) (http://postimg.org/image/ygnh816tr/)
(http://s19.postimg.org/6hxwuwukv/2014_12_20_1167.jpg) (http://postimg.org/image/6hxwuwukv/)
Ubaceni klipovi i glava poravnata i skinuta za pola mm :)
(http://s19.postimg.org/3ui3vex8v/2014_12_22_1170.jpg) (http://postimg.org/image/3ui3vex8v/)
(http://s19.postimg.org/odd00hb67/2014_12_22_1169.jpg) (http://postimg.org/image/odd00hb67/)
Postavljena glava i klackalice i stegnuto :)
(http://s19.postimg.org/ffols4r7z/2014_12_23_1173.jpg) (http://postimg.org/image/ffols4r7z/)
(http://s19.postimg.org/om6wfewgf/2014_12_23_1174.jpg) (http://postimg.org/image/om6wfewgf/)
Motor se polako sastavlja :cool:
Usput koje bi ulje nasuo, viskozitet? :)
(http://s19.postimg.org/tb14z76q7/2014_12_27_1175.jpg) (http://postimg.org/image/tb14z76q7/)
(http://s19.postimg.org/a77tiutvz/2014_12_27_1176.jpg) (http://postimg.org/image/a77tiutvz/)
(http://s19.postimg.org/v1k60oo9b/2014_12_27_1177.jpg) (http://postimg.org/image/v1k60oo9b/)
(http://s19.postimg.org/jvpuzqe33/2014_12_27_1178.jpg) (http://postimg.org/image/jvpuzqe33/)
(http://s19.postimg.org/qjhv8l87j/2014_12_27_1179.jpg) (http://postimg.org/image/qjhv8l87j/)
(http://s19.postimg.org/rztdqqb4f/2014_12_27_1180.jpg) (http://postimg.org/image/rztdqqb4f/)
Napravljeni nosaci pumpe, s kojim cu posle ucentrirati na Fiatov blok :)
(http://s19.postimg.org/dn6gmq18v/2015_01_16_1218.jpg) (http://postimg.org/image/dn6gmq18v/)
(http://s19.postimg.org/jcmp717f3/2015_01_16_1217.jpg) (http://postimg.org/image/jcmp717f3/)
(http://s19.postimg.org/7osnchia7/2015_01_16_1216.jpg) (http://postimg.org/image/7osnchia7/)
(http://s19.postimg.org/wjc56k34f/2015_01_16_1219.jpg) (http://postimg.org/image/wjc56k34f/)
(http://s19.postimg.org/3w94wr2rz/2015_01_16_1220.jpg) (http://postimg.org/image/3w94wr2rz/)
Napravljen adapter(medju ploca) :)
(http://s19.postimg.org/7vbecoxqn/2015_01_17_1222.jpg) (http://postimg.org/image/7vbecoxqn/)
(http://s19.postimg.org/b3fvpqk0f/2015_01_17_1224.jpg) (http://postimg.org/image/b3fvpqk0f/)
(http://s19.postimg.org/ogj0scoun/2015_01_17_1221.jpg) (http://postimg.org/image/ogj0scoun/)
Pumpa skracena, nacentrirana i zavarena :)
(http://s19.postimg.org/4uh8aaz7z/2015_01_21_1226.jpg) (http://postimg.org/image/4uh8aaz7z/)
(http://s19.postimg.org/w6chbn3yn/2015_01_21_1225.jpg) (http://postimg.org/image/w6chbn3yn/)
(http://s19.postimg.org/4rxcngvkf/2015_01_21_1227.jpg) (http://postimg.org/image/4rxcngvkf/)
(http://s19.postimg.org/7ib9yehn3/2015_01_21_1228.jpg) (http://postimg.org/image/7ib9yehn3/)
(http://s19.postimg.org/cypcf1ln3/2015_01_21_1230.jpg) (http://postimg.org/image/cypcf1ln3/)
(http://s19.postimg.org/cr1pijaof/2015_01_21_1231.jpg) (http://postimg.org/image/cr1pijaof/)
(http://s19.postimg.org/l817tgfdb/2015_01_21_1233.jpg) (http://postimg.org/image/l817tgfdb/)
(http://s19.postimg.org/ty2w81m8f/2015_01_21_1236.jpg) (http://postimg.org/image/ty2w81m8f/)
(http://s19.postimg.org/uovmdtolr/20150121_201643.jpg) (http://postimg.org/image/uovmdtolr/)
(http://s19.postimg.org/kg35800jz/20150121_201439.jpg) (http://postimg.org/image/kg35800jz/)
Ok sve ce biti objavljeno :)
(http://s19.postimg.org/rgieso4i7/2015_01_22_1238.jpg) (http://postimg.org/image/rgieso4i7/)
Aha, hvala na odgovoru :)
Evo masinica je upalilaa :moron:
https://www.youtube.com/watch?v=m4bK50cyPoI&feature=youtu.be (https://www.youtube.com/watch?v=m4bK50cyPoI&feature=youtu.be)
Skalapa se i 850, nabavio sam klip koji mi je hvalio :)
i slucajno u garazi nadjem bragastu uzmem pomicno mjerilo, kad ono specijalova brega (35mm bregovi):losi-zubi::huepfenred: nju cu da stavim u ovaj motor :D
Izduve sam vec ranije prosirio na 27 mm
i usis 27mm sa 57mm
Jos planiram spustiti glavu, a nezz koliko bi najbolje bilo, sta vi mislite? :D
(http://s19.postimg.org/y7f2d89jj/11063358_789211271162138_482343260_n.jpg) (http://postimg.org/image/y7f2d89jj/)
(http://s19.postimg.org/iknszuvrj/11040817_789220087827923_1935024368_n.jpg) (http://postimg.org/image/iknszuvrj/)
(http://s19.postimg.org/ldh0jvw3z/11022942_789212014495397_1000275244_n.jpg) (http://postimg.org/image/ldh0jvw3z/)
Spustena glava za 1.5mm :)
(http://s19.postimg.org/6n0zhh6j3/20150318_102835.jpg) (http://postimg.org/image/6n0zhh6j3/)
(http://s19.postimg.org/r8fr9do3z/20150318_102816.jpg) (http://postimg.org/image/r8fr9do3z/)
Produbljeni kanali za vodu
(http://s19.postimg.org/tn7mtt4cv/20150318_111239.jpg) (http://postimg.org/image/tn7mtt4cv/)
i namontirana :)
(http://s19.postimg.org/q8u1reybz/20150318_171126.jpg) (http://postimg.org/image/q8u1reybz/)
(http://s19.postimg.org/l8s05q3bj/20150318_173240.jpg) (http://postimg.org/image/l8s05q3bj/)
-
Evo i bregaste od speciala :biggrin:
(http://s19.postimg.org/sfyafc3m7/20150319_100701.jpg) (http://postimg.org/image/sfyafc3m7/)
-
Produbio sam lezaj, da bi mogla da udje specialova bregasta, malo sam improvizovao :D
Morao sam praviti nastavak za glodalo od vijka M8 i tiple celicne za beton
Evo kako izgleda...
(http://s19.postimg.org/mnkumc6kv/20150319_193255.jpg) (http://postimg.org/image/mnkumc6kv/)
(http://s19.postimg.org/jfgd9akb3/20150319_193305.jpg) (http://postimg.org/image/jfgd9akb3/)
Pa sam krenuo u akciju...
(http://s19.postimg.org/fyiwk2amn/20150319_194042.jpg) (http://postimg.org/image/fyiwk2amn/)
(http://s19.postimg.org/k3p7s8j0v/20150319_200926.jpg) (http://postimg.org/image/k3p7s8j0v/)
(http://s19.postimg.org/7vkq8qq1b/20150319_201738.jpg) (http://postimg.org/image/7vkq8qq1b/)
(http://s19.postimg.org/aodxsrqdr/20150319_201749.jpg) (http://postimg.org/image/aodxsrqdr/)
-
Dobar Fićo, svaka čast :palacgore:
-
Hvala :biggrin:
-
Produbio sam lezaj, da bi mogla da udje specialova bregasta, malo sam improvizovao :D
mislis prosirija?
kolko imas iskustva s sklapanjem makina od auta?
-
Odličan!
-
mislis prosirija?
kolko imas iskustva s sklapanjem makina od auta?
Trebalo samo produbiti(prosiriti) na jednom dijelu lezaj u dubini od 2mm i sirini od 6-7mm do sredine lezaja, da breg moze proci kroz lezaj , posto su u ove bregaste veci bregovi od standarda :biggrin:
Kad treba da udje u srednji lezaj, breg zapne i onda kad se na tom dijelu produbi, on udje u tu rupu i bregasta se gurne do kraja :biggrin:
(http://s19.postimg.org/o94prw66n/20150319_194042.jpg) (http://postimg.org/image/o94prw66n/)
Precnici lezaja su isti na obe bregaste...
Ovo mi je 2. motor sto skalpam od 0
Prvi je ovaj gore Fiatov(A112) :mrgreen:
Odličan!
Hvala :biggrin:
-
što reći nego,svaka čast na znanju, volji, snalažljivosti...
-
Hvala :biggrin:
-
tako da,prvo san mislija da si sirija cili lezaj
-
Sta mislite koji karburator da stavim :biggrin:
-
dupli weber 23/21 ili 23/23 sa fiata 850 sporta-pogođeno za tu makinu
-
Stavi ie :mrgreen:
(http://s23.postimg.org/ypn0jxlsn/IMAG0144.jpg) (http://postimg.org/image/ypn0jxlsn/)
-
dupli weber 23/21 ili 23/23 sa fiata 850 sporta-pogođeno za tu makinu
Ti karburatori se teze nalaze, mislio sam staviti od juga 32 :misli:
Stavi ie :mrgreen:
(http://s23.postimg.org/ypn0jxlsn/IMAG0144.jpg) (http://postimg.org/image/ypn0jxlsn/)
Uff to je koplikovano, ipak cuja jednostavnije :mrgreen:
-
karburator je zakon pogotovo duplak samo je problem sta je to vec sve istroseno i nikakvo tribalo bi nač novi
-
jbg, da hoce naleti polovan i dobar, uzeo bih ga :biggrin:
-
Sasija je vecinom ogoljena
(http://s19.postimg.org/cvei5p45r/20150322_130532.jpg) (http://postimg.org/image/cvei5p45r/)
(http://s19.postimg.org/i83cjts27/20150322_130539.jpg) (http://postimg.org/image/i83cjts27/)
(http://s19.postimg.org/6gfh90xfz/20150322_130634.jpg) (http://postimg.org/image/6gfh90xfz/)
Na ovom dijelu je ispucao, kako bi bilo najpametnije ovo rijesiti?
ispraviti, navariti limenu plocu na patos i unutra u blatobranu lim oblikovati i zavariti...
(http://s19.postimg.org/h733upb2n/20150322_160257.jpg) (http://postimg.org/image/h733upb2n/)
(http://s19.postimg.org/80kt7f5u7/20150322_160337.jpg) (http://postimg.org/image/80kt7f5u7/)
-
Napravio sam i stalak za motor sa tockicima, da ne lomim ledja kad ga treba napolje iznijet :mrgreen:
(http://s19.postimg.org/ty9ijdxe7/20150415_201510.jpg) (http://postimg.org/image/ty9ijdxe7/)
(http://s19.postimg.org/8uzlbmq8f/20150415_204238.jpg) (http://postimg.org/image/8uzlbmq8f/)
A sad razvodnik :smile:
Uzeta osovinica od fice i narezan navoj i uvrnuta u osovinu razvodnika, i donji dio ostrugan da moze proci kroz razvodnik
Evo slike
(http://s19.postimg.org/8tahqv5fz/20150409_121819.jpg) (http://postimg.org/image/8tahqv5fz/)
(http://s19.postimg.org/j4mujix5b/20150409_121908.jpg) (http://postimg.org/image/j4mujix5b/)
(http://s19.postimg.org/dojcghmq7/20150416_173913.jpg) (http://postimg.org/image/dojcghmq7/)
(http://s19.postimg.org/aiyqqa43z/20150416_173939.jpg) (http://postimg.org/image/aiyqqa43z/)
Malo je poklopac kucnut i oturpijan razvodnik
(http://s19.postimg.org/gz7pgdcnj/20150416_174009.jpg) (http://postimg.org/image/gz7pgdcnj/)
(http://s19.postimg.org/6dsw1hcnj/20150416_173958.jpg) (http://postimg.org/image/6dsw1hcnj/)
(http://s19.postimg.org/b9rgw26hb/20150416_222503.jpg) (http://postimg.org/image/b9rgw26hb/)
-
Nabavio i karburator 34mm za speciala :hura:
(http://s19.postimg.org/y2ljwegcv/20150420_200942.jpg) (http://postimg.org/image/y2ljwegcv/)
(http://s19.postimg.org/b2ewk2ij3/20150420_200935.jpg) (http://postimg.org/image/b2ewk2ij3/)
(http://s19.postimg.org/yhwtpf2a7/20150420_200925.jpg) (http://postimg.org/image/yhwtpf2a7/)
-
sta radis s razvodnikom stavljas elektronski ili...
-
Da elektronski stavljam na fiat motor
(http://s19.postimg.org/qqg3quy4v/20150418_180016.jpg) (http://postimg.org/image/qqg3quy4v/)
a na specialu ce ostati s platinama :smile:
-
:palacgore: :palacgore:
-
Ponekad se nadje vremena i za ficu :biggrin:
trenutno je na "krovu" radi se pod i sve sto je pod njim :biggrin:
(http://s19.postimg.org/lx85t2klr/IMG_1437573557815_V.jpg) (http://postimg.org/image/lx85t2klr/)
(http://s19.postimg.org/lx85t2klr/IMG_1437573557815_V.jpg) (http://postimg.org/image/lx85t2klr/)
(http://s19.postimg.org/r9x0778i7/20150908_212958.jpg) (http://postimg.org/image/r9x0778i7/)
(http://s19.postimg.org/r9x0778i7/20150908_212958.jpg) (http://postimg.org/image/r9x0778i7/)
(http://s19.postimg.org/jdciyyx1r/20150908_205324.jpg) (http://postimg.org/image/jdciyyx1r/)
-
:misli: :misli: ne varis valjda sve elektro :misli: :misli:
-
vjerovatno nešto elektro, a nešto lučno :wink:
-
:shock: :shock: vidim gore masku od elektro pa si mislim nije valjda ...... :kokice: :kokice:
-
Sve varim sa ovim :smile:
nedavno sam ga nabavio pa jos nisam masku za njega
Varstroj Varming 251
(http://s19.postimg.org/tl8uglnf3/20150703_162135.jpg) (http://postimg.org/image/tl8uglnf3/)
(http://s19.postimg.org/arn1jlp73/20150703_162144.jpg) (http://postimg.org/image/arn1jlp73/)
(http://s19.postimg.org/qfo8qe4sv/20150711_095556.jpg) (http://postimg.org/image/qfo8qe4sv/)
-
:mrgreen: :mrgreen: odlicna ideja bas su na mom riknuli ovi kotaci od napred
-
na posao onda :mrgreen:
-
Osvjezenje :mrgreen:
copy/paste fica forum :biggrin:
BT80 - 13-12-2015 u 00:49
Da tema ne zastari bas puno :)
(http://s19.postimg.org/brynso5hr/20151212_143643.jpg)
(http://s19.postimg.org/9oo8l05ov/20151212_143720.jpg)
(http://s19.postimg.org/431tgy4zz/20151212_143729.jpg)
(http://s19.postimg.org/l2arw7g7j/20151212_150542.jpg)
mikicak - 13-12-2015 u 15:51
- ma nece tema da zastari ,nego da se ti ne olenjis:cigara::ok:
BT80 - 14-12-2015 u 13:42
Ma necu :D :ok:
Samo je dosta usporeno zbog faxa
BT80 - 14-9-2016 u 14:41
Radi se po malo :D
Komentarisite, pisite sta ne valja :)
(https://s19.postimg.org/9spjsenbj/IMG_20160720_194906.jpg)
(https://s19.postimg.org/rk166v2q7/IMG_20160720_194916.jpg)
(https://s19.postimg.org/snlaitndb/IMG_20160720_194948.jpg)
(https://s19.postimg.org/gmzui3fyn/IMG_20160722_194403.jpg)
(https://s19.postimg.org/tsjy1xz7z/IMG_20160723_133608.jpg)
(https://s19.postimg.org/z58sg2n4f/IMG_20160727_204529.jpg)
(https://s19.postimg.org/l02ze9e33/IMG_20160727_204536.jpg)
(https://s19.postimg.org/89yr1664v/IMG_20160727_204602.jpg)
(https://s19.postimg.org/ilb3ttxu7/IMG_20160727_204824.jpg)
(https://s19.postimg.org/t9euso7tb/IMG_20160727_204829.jpg)
(https://s19.postimg.org/oc1a7k5u7/IMG_20160727_204835.jpg)
Prepravka za Nivine amortizere...
(https://s19.postimg.org/w61vsydn3/IMG_20160803_131120.jpg)
(https://s19.postimg.org/xmdeb3gjz/IMG_20160803_131130.jpg)
(https://s19.postimg.org/6d20wlfgv/IMG_20160803_203740.jpg)
Icice dvije ploce, deblja 4mm i tanja 3mm, mislim da je dovoljna debljina???
Trenutno su privremeno dvije tanje od 3mm od lijeve i desne strane
(https://s19.postimg.org/ou1115ksv/IMG_20160803_203748.jpg)
(https://s19.postimg.org/uw8nrn98v/IMG_20160814_131518.jpg)
(https://s19.postimg.org/dwzpcdy1b/IMG_20160814_131532_1.jpg)
(https://s19.postimg.org/g2u06w1hr/received_1074808045935791.jpg)
mikicak - 14-9-2016 u 21:31
:aplauz: :aplauz: ide tebi to od ruke ,samo napred.koja je uloga ove zatege na zadnjoj slici :stidise::JELEN_pivo:
BT80 - 14-9-2016 u 23:18
Hvala :D
Zatega sluzi da eliminise minimalno pomijeranje gibnja npr. u krivinama, to sam vidio da rade kad prave ficu za trke :cool: :lizalica:
Krle - 15-9-2016 u 10:40
Svaka čast stvarno, uživanje je videti ovakav rad.
BT80 - 15-9-2016 u 12:40
Hvala, hvala :D
Po malo se gituje...
(https://s19.postimg.org/4qm02ui6n/IMG_20160914_151123.jpg)
(https://s19.postimg.org/q1jk740b3/IMG_20160914_151143.jpg)
(https://s19.postimg.org/6kyukl573/IMG_20160914_151148.jpg)
BT80 - 5-10-2016 u 22:54
Malo sam se igrao oko volana :D
Ovakav je bio...
(https://s19.postimg.org/7ltmgrbf3/received_1115017608581501.jpg)
Pa je na ovo izasao
(https://s19.postimg.org/5wkj8ovpr/received_1115018311914764.jpg)
(https://s19.postimg.org/4iswddwgf/received_1115018318581430.jpg)
Malo je red slika pobrkan
(https://s19.postimg.org/6bvt1phn3/received_1115018271914768.jpg)
(https://s19.postimg.org/einsta7pr/received_1115018288581433.jpg)
(https://s19.postimg.org/sqi2vo9sf/received_1115018295248099.jpg)
(https://s19.postimg.org/7i4ee8vbj/received_1115018251914770.jpg)
(https://s19.postimg.org/cut8sdj7z/received_1115018265248102.jpg)
(https://s19.postimg.org/jzb21eqhb/received_1115018221914773.jpg)
(https://s19.postimg.org/dmvwrknf3/received_1115018231914772.jpg)
(https://s19.postimg.org/kembufcen/received_1115018205248108.jpg)
(https://s19.postimg.org/whrnhzngv/received_1115018211914774.jpg)
(https://s19.postimg.org/b9dz0k8zz/received_1115018195248109.jpg)
mikicak - 6-10-2016 u 10:11
- pa lepo si se igrao, rezultat je :aplauz::aplauz:
BT80 - 6-10-2016 u 12:12
Velim bio 5e pa da malo experimentisem :)
BT80 - 6-10-2016 u 22:02
Posle duzeg vremena okrenut fićko :)
(https://s19.postimg.org/lmj3ozczz/IMG_20161003_185751.jpg)
(https://s19.postimg.org/x05n06nin/IMG_20161003_183213.jpg)
(https://s19.postimg.org/aphs07q8f/IMG_20161003_182645.jpg)
(https://s19.postimg.org/eadnjfurz/IMG_20161003_181720.jpg)
(https://s19.postimg.org/wr82a9aq7/IMG_20161003_181709.jpg)
mikicak - 7-10-2016 u 12:20
-i sta kazu komsije i rodbina :cigara::ok::deda:
BT80 - 10-10-2016 u 22:55
Haha, svecano prevrtanje i kad cemo se vozat :gremlini:
BT80 - 11-11-2016 u 20:13
Radi se po malo :)
(https://s19.postimg.org/5me194g0f/IMG_20161013_181547.jpg)
(https://s19.postimg.org/ju3pxrspb/IMG_20161015_162228.jpg)
(https://s19.postimg.org/6rcos8rv3/IMG_20161022_141102.jpg)
(https://s19.postimg.org/50tnqrabz/IMG_20161022_151442.jpg)
(https://s19.postimg.org/c5bgzshlb/IMG_20161024_180841.jpg)
(https://s19.postimg.org/l1m93q87j/IMG_20161024_180849.jpg)
BT80 - 15-11-2016 u 19:39
(https://s19.postimg.org/bbm04p5an/IMG_20161113_102805.jpg)
(https://s19.postimg.org/49snw8r2n/IMG_20161113_102818.jpg)
gif upload
mikicak - 16-11-2016 u 10:19
-bravo,svaka ti cast ,ti si jedini koji nesto radis na ovom forumu.ja kad god se ukljucim u zadnjih nedelju dana stalno mi pokazuje gresku ,pa sam mislio da sam promasio forum.samo napred.:ok::JELEN_pivo::deda:
BT80 - 16-11-2016 u 17:10
Hvala, drago mi je, trudim se da sve sto uradim objavim ovd'e :) hehe
BT80 - 20-11-2016 u 18:47
(https://s19.postimg.org/r2h6sk173/IMG_20161118_124232.jpg)
(https://s19.postimg.org/x4otj1pn3/IMG_20161120_120232.jpg)
gigi - 21-11-2016 u 09:10
Nikada se nisam petljao sa prepravkom u kabrio varijantu te upravo zbog toga i pitanje,da li je ojačanje koje si napravio dovoljno da karoserija ne "radi" usled uklanjanja konstrukcije krova?
BT80 - 23-11-2016 u 23:18
U kabrio je prepravljen 90-ih i sa dosta manje ojacanja koja nisu bila zavarena za karoseriju nego zasarafana, nije se savijao, a sad da ne pricam i jos su vrata zavarena, prije su se otvarala. Ipak treba biti malo vise ojacanja zbog jaceg motora :)
Kad se ima vremena ponesto se uradi :D
(https://s19.postimg.org/69yj98gzz/IMG_20161123_160658.jpg)
(https://s19.postimg.org/6nzv8u13j/IMG_20161123_160705.jpg)
BT80 - 26-11-2016 u 18:56
:gremlini:
(https://s19.postimg.org/cok8k20i7/IMG_20161126_112342.jpg)
(https://s19.postimg.org/71nvmkxzj/IMG_20161126_112350.jpg)
(https://s19.postimg.org/4ydgewy6n/IMG_20161126_161833.jpg)
(https://s19.postimg.org/42q5qy39r/IMG_20161127_112457.jpg)
(https://s19.postimg.org/xj5rtd9n3/IMG_20161127_112503.jpg)
(https://s19.postimg.org/nzw2zwm4v/IMG_20161127_114630.jpg)
BT80 - 4-12-2016 u 15:37
:)
(https://s19.postimg.org/xzk50q7tb/IMG_20161204_142749.jpg)
(https://s19.postimg.org/4yfsrbndb/IMG_20161204_142801.jpg)
(https://s19.postimg.org/jvsv62pzj/IMG_20161204_142816.jpg)
(https://s19.postimg.org/fny2xbojz/IMG_20161204_142834.jpg)
gici1 - 4-12-2016 u 16:44
:aplauz::aplauz::aplauz: dupla đunta sa sitnim nutom...opa Đurđo...ako su ti ispravni rukavci i nemaš lufta u lagerima ima da ti traje 20 godina...ja vozim na duple đunte od 90. Sad si miran...
BT80 - 4-12-2016 u 17:09
Rukavci su bez lufta i skf novi lageri :D
Tu ideju sam pokupio sa foruma, mozda sam i od tebe vidio, pa da probam... :afro:
gici1 - 5-12-2016 u 14:09
hehehe ja pisao o tome stavljao slike a mnogi viču ,ne može,ne valja... :obrve:
BT80 - 5-12-2016 u 19:46
Pravo rjesenje, em sto duuze traje i plus imaju dva gumigelinga po tocku, jos su manji udari i duze ce trajat mjenjac i svi spojnicki sklopovi :gremlini:
gici1 - 6-12-2016 u 11:36
zglobovi što menjaju prirubnicu će vremenom da se malo omekšaju i rasklimaju ,ali nema šanse da provrte...ali to se neće desiti barem 20 + hiljada km... :azn:
BT80 - 6-12-2016 u 20:09
Dobro je moci ce to dugo biti, za 5 godina necu toliko preci :D
-
Svaka čast!
Pretpostavljam da nejde na regu!
-
Hvala :biggrin:
Prvo ga trebam atestovati, pa onda rega.
-
Kako bi mu stajale ove felne? :misli:
(https://s19.postimg.org/ff0yqrspb/IMG_20161209_162838.jpg) (https://postimg.org/image/ff0yqrspb/)
Napravio sam nekakvu izduvnu granu :smile:
Ako neko ima kakvu skicu lonca, slobodno neka okaci bio bih zahvalan hehe
Inace grana je bila od Yamahe r1 :mrgreen:
(https://s19.postimg.org/alvwtvy8f/IMG_20160705_211314.jpg) (https://postimg.org/image/alvwtvy8f/)
(https://s19.postimg.org/xzzas2qrz/IMG_20161207_163133.jpg) (https://postimg.org/image/xzzas2qrz/)
(https://s19.postimg.org/4m85q8dfz/IMG_20161207_165019.jpg) (https://postimg.org/image/4m85q8dfz/)
(https://s19.postimg.org/509hptxjj/IMG_20161210_162311.jpg) (https://postimg.org/image/509hptxjj/)
(https://s19.postimg.org/xeex9pl3j/IMG_20161210_162323.jpg) (https://postimg.org/image/xeex9pl3j/)
(https://s19.postimg.org/n5mg3vx1r/IMG_20161212_150259.jpg) (https://postimg.org/image/n5mg3vx1r/)
(https://s19.postimg.org/as9lwz7db/IMG_20161212_150315.jpg) (https://postimg.org/image/as9lwz7db/)
(https://s19.postimg.org/bj2c2r9qn/IMG_20161212_150820.jpg) (https://postimg.org/image/bj2c2r9qn/)
(https://s19.postimg.org/gvr6gvxn3/IMG_20161212_175003.jpg) (https://postimg.org/image/gvr6gvxn3/)
(https://s19.postimg.org/8ero5ysy7/IMG_20161212_175013.jpg) (https://postimg.org/image/8ero5ysy7/)
(https://s19.postimg.org/9ibshxdlb/IMG_20161212_180810.jpg) (https://postimg.org/image/9ibshxdlb/)
-
:smile:
(https://s19.postimg.org/md7vshwy7/IMG_20161214_122124.jpg) (https://postimg.org/image/md7vshwy7/)
(https://s19.postimg.org/63hpplma7/IMG_20161214_122133.jpg) (https://postimg.org/image/63hpplma7/)
(https://s19.postimg.org/msj5liivj/IMG_20161214_122142.jpg) (https://postimg.org/image/msj5liivj/)
(https://s19.postimg.org/y65owpte7/IMG_20161214_122147.jpg) (https://postimg.org/image/y65owpte7/)
(https://s19.postimg.org/kdra132mn/IMG_20161214_122309.jpg) (https://postimg.org/image/kdra132mn/)
(https://s19.postimg.org/4gsi4da8f/IMG_20161214_122314.jpg) (https://postimg.org/image/4gsi4da8f/)
(https://s19.postimg.org/d0bw24ikv/IMG_20161214_122323.jpg) (https://postimg.org/image/d0bw24ikv/)
(https://s19.postimg.org/ded81q2of/IMG_20161216_153603.jpg) (https://postimg.org/image/ded81q2of/)
(https://s19.postimg.org/71y2rvzm7/IMG_20161216_153624.jpg) (https://postimg.org/image/71y2rvzm7/)
(https://s19.postimg.org/flm23dxcf/IMG_20161216_171223.jpg) (https://postimg.org/image/flm23dxcf/)
(https://s19.postimg.org/5ctkxk9an/IMG_20161217_215135.jpg) (https://postimg.org/image/5ctkxk9an/)
(https://s19.postimg.org/uk4gxtcen/IMG_20161221_155848.jpg) (https://postimg.org/image/uk4gxtcen/)
(https://s19.postimg.org/y50ch1gy7/IMG_20161221_161028.jpg) (https://postimg.org/image/y50ch1gy7/)
-
To je metalik baza i gore 2K bezbojni? Stavljao si primer ispod?
Inače jako su ti fino ispale felge. :yes:
-
Prajmer ispod, a nije metalik boja, akrilna je sa zrncima bez laka, mene je zacudilo kako je fino ispalo i dobro se sjaji :biggrin:
-
Kako bi mu stajale ove felne? :misli:
(https://s19.postimg.org/ff0yqrspb/IMG_20161209_162838.jpg) (https://postimg.org/image/ff0yqrspb/)
Napravio sam nekakvu izduvnu granu :smile:
Ako neko ima kakvu skicu lonca, slobodno neka okaci bio bih zahvalan hehe
Inace grana je bila od Yamahe r1 :mrgreen:
(https://s19.postimg.org/alvwtvy8f/IMG_20160705_211314.jpg) (https://postimg.org/image/alvwtvy8f/)
(https://s19.postimg.org/xzzas2qrz/IMG_20161207_163133.jpg) (https://postimg.org/image/xzzas2qrz/)
(https://s19.postimg.org/4m85q8dfz/IMG_20161207_165019.jpg) (https://postimg.org/image/4m85q8dfz/)
(https://s19.postimg.org/509hptxjj/IMG_20161210_162311.jpg) (https://postimg.org/image/509hptxjj/)
(https://s19.postimg.org/xeex9pl3j/IMG_20161210_162323.jpg) (https://postimg.org/image/xeex9pl3j/)
(https://s19.postimg.org/n5mg3vx1r/IMG_20161212_150259.jpg) (https://postimg.org/image/n5mg3vx1r/)
(https://s19.postimg.org/as9lwz7db/IMG_20161212_150315.jpg) (https://postimg.org/image/as9lwz7db/)
(https://s19.postimg.org/bj2c2r9qn/IMG_20161212_150820.jpg) (https://postimg.org/image/bj2c2r9qn/)
(https://s19.postimg.org/gvr6gvxn3/IMG_20161212_175003.jpg) (https://postimg.org/image/gvr6gvxn3/)
(https://s19.postimg.org/8ero5ysy7/IMG_20161212_175013.jpg) (https://postimg.org/image/8ero5ysy7/)
(https://s19.postimg.org/9ibshxdlb/IMG_20161212_180810.jpg) (https://postimg.org/image/9ibshxdlb/)
grane pomotaj najprije prema naprijed da bi ih potom iznad zadnje poluosovine objedinio u jednu cijev i potom ko na skuteru stavio koljeno od 180 stupnjeva i na kraj zadnji protočni lonac od z101/y55-rezultat je fenomenalan tako smo mi na našem figuaru napravili
-
Vec sam ih pomotao ka nazad, fali mi lonac, a posto hocu da idu dvije cijevi ne mogu staviti lonac od z101, pa cu praviti sa 2 cijevi, ako imas kakvu skicu protocnog lonca slobodno okaci ili predlog kako da napravim :wink: :biggrin:
Ja sam mislio da uzmem dvije cijevi izbusim ih citavom duzinom po cijeloj povrsini strpam u lonac i okolo sitna metalna vuna...
-
nepotrebno se mučiš a i svi na tim mašinama objedinjuju cjevi u jedan lonac
-
Radim po uzoru ovog auspuha:
(https://s19.postimg.org/ibve0ku1b/received_1565774723438745.jpg) (https://postimg.org/image/ibve0ku1b/)
Svidja mi se ovaj pa hocu da bude sa dvije cijevi... :smile:
-
ok
to je šminka aftermarket auspuh sa početka sedamdesetih
bilo ih je dosta kod nas-bučan je
-
Imas u teslicu fabriku auspuha pa ako ti treba nesto mozes kod njih naci
-
Znam, al skuplje mi je tako, ovako malo se zanimam kad imam vremena nije mi zurba...
-
:smile:
(https://s19.postimg.org/s7md5zn67/IMG_20170104_171242.jpg) (https://postimg.org/image/s7md5zn67/)
(https://s19.postimg.org/tnxvo4q33/IMG_20170104_171251.jpg) (https://postimg.org/image/tnxvo4q33/)
(https://s19.postimg.org/sa68stqtr/IMG_20170104_171516.jpg) (https://postimg.org/image/sa68stqtr/)
(https://s19.postimg.org/6p1657u33/IMG_20170105_180647.jpg) (https://postimg.org/image/6p1657u33/)
(https://s19.postimg.org/hd4x42427/IMG_20170123_133500.jpg) (https://postimg.org/image/hd4x42427/)
(https://s19.postimg.org/rbuh4a2vj/IMG_20170123_133522.jpg) (https://postimg.org/image/rbuh4a2vj/)
(https://s19.postimg.org/s2n7a258v/IMG_20170123_152743.jpg) (https://postimg.org/image/s2n7a258v/)
(https://s19.postimg.org/pzcs2e5fz/IMG_20170123_152751.jpg) (https://postimg.org/image/pzcs2e5fz/)
(https://s19.postimg.org/cwh5j4f7z/IMG_20170123_152824.jpg) (https://postimg.org/image/cwh5j4f7z/)
(https://s19.postimg.org/3pyuvu9zj/IMG_20170123_155422.jpg) (https://postimg.org/image/3pyuvu9zj/)
(https://s19.postimg.org/cz115yivj/IMG_20170123_155432.jpg) (https://postimg.org/image/cz115yivj/)
-
čekamo snimak da vidimo kako prede :palacgore:
-
Bice, bice samo strpljivo :mrgreen:
-
Ugradjeno elektronsko paljenje :mrgreen:
I nove champion svjecice
(https://s19.postimg.org/4xg237n67/IMG_20170131_152453.jpg) (https://postimg.org/image/4xg237n67/)
(https://s19.postimg.org/8igj06h3j/IMG_20170131_152458.jpg) (https://postimg.org/image/8igj06h3j/)
(https://s19.postimg.org/vxyg5j0un/IMG_20170131_180055.jpg) (https://postimg.org/image/vxyg5j0un/)
(https://s19.postimg.org/gqigl68zz/IMG_20170201_174136.jpg) (https://postimg.org/image/gqigl68zz/)
(https://s19.postimg.org/kbec4edjj/IMG_20170201_180446.jpg) (https://postimg.org/image/kbec4edjj/)
(https://s19.postimg.org/nwa7nmi33/IMG_20170204_170130.jpg) (https://postimg.org/image/nwa7nmi33/)
(https://s19.postimg.org/91lm9g8i7/IMG_20170204_173247.jpg) (https://postimg.org/image/91lm9g8i7/)
-
Ako su svjećice made in Belgija,nisi se usrećio sa njima,imam jako loša iskustva,francuske i engleske su dobre.
-
Pise made in France, 3e je komad bio, valjda ce valjati...
-
koje si paljenje upasa od čega??
-
Audi 80, 1.8...
-
moga si stavit video da čujemo zvuk
-
Moze, ali trenutno je fabricki auspuh...
-
mislija san da si stavija onaj sta si sam radija
-
Kad stavim daj bice video, jos nije zavrsen :palacgore:
-
bas me zanima kako ce se cut,prijatelj je počea slagat ficu pa da znam dat prijedlog
-
Bucan je, u leru nije doliko, a kad odrezes gas para uši :mrgreen:
-
Ugradjen jugov karburator
Ofarban auspuh i namontiran :biggrin:
(https://s19.postimg.org/q3dmjvehb/IMG_20170220_140453.jpg) (https://postimg.org/image/q3dmjvehb/)
(https://s19.postimg.org/rwgj86znz/IMG_20170220_140502.jpg) (https://postimg.org/image/rwgj86znz/)
(https://s19.postimg.org/lwss4jevj/IMG_20170221_180101.jpg) (https://postimg.org/image/lwss4jevj/)
(https://s19.postimg.org/ypgw4gqhb/IMG_20170221_180112.jpg) (https://postimg.org/image/ypgw4gqhb/)
(https://s19.postimg.org/nra800r9r/IMG_20170221_223623.jpg) (https://postimg.org/image/nra800r9r/)
(https://s19.postimg.org/62ih8efin/IMG_20170221_224854.jpg) (https://postimg.org/image/62ih8efin/)
(https://s19.postimg.org/jkpdkornz/IMG_20170224_155025.jpg) (https://postimg.org/image/jkpdkornz/)
(https://s19.postimg.org/7wvbq52j3/IMG_20170224_155030.jpg) (https://postimg.org/image/7wvbq52j3/)
(https://s19.postimg.org/9py8egnpr/IMG_20170225_151224.jpg) (https://postimg.org/image/9py8egnpr/)
(https://s19.postimg.org/joj70xx5b/IMG_20170227_154431.jpg) (https://postimg.org/image/joj70xx5b/)
(https://s19.postimg.org/rijsmc4y7/IMG_20170227_154854.jpg) (https://postimg.org/image/rijsmc4y7/)
Evo i video zvuka asupuha, mada nije to to k'o uzivo :smile:
https://www.youtube.com/watch?v=DkTeeDuu5cM&feature=youtu.be (https://www.youtube.com/watch?v=DkTeeDuu5cM&feature=youtu.be)
-
odlično :palacgore: samo za moj gust malo "tih" auspuh :mrgreen:
-
Meni je bas moćan zvuk, kogod je cuo uzivo dopao mu se :mrgreen:
-
Meni je isto super, fini zvuk kao da je puno veće kubikaže :palacgore:
-
:palacgore: :mrgreen: samo nek se cuje
-
Fino napreduje. :)
Cime si cistio karburator? (otkuhan u detrdjentu?)
-
:palacgore:
-
Al će ovo bit gušt vozit :mrgreen:
-
Fino napreduje. :)
Cime si cistio karburator? (otkuhan u detrdjentu?)
prvo u benzinu opran, pa onda u deterdzentu otkuhan :smile:
:palacgore:
:biggrin:
Al će ovo bit gušt vozit :mrgreen:
trebalo bi :mrgreen:
-
Tx
-
Radilo se i oko fićka :biggrin:
(https://s19.postimg.org/kye6ye973/IMG_20170227_175716.jpg) (https://postimg.org/image/kye6ye973/)
(https://s19.postimg.org/fa7w7ex3z/IMG_20170303_192550.jpg) (https://postimg.org/image/fa7w7ex3z/)
(https://s19.postimg.org/6ryg310v3/IMG_20170303_192559.jpg) (https://postimg.org/image/6ryg310v3/)
(https://s19.postimg.org/vxze9wk5r/IMG_20170303_193749.jpg) (https://postimg.org/image/vxze9wk5r/)
(https://s19.postimg.org/px1pcx5a7/IMG_20170305_103548.jpg) (https://postimg.org/image/px1pcx5a7/)
(https://s19.postimg.org/lnwzarp67/IMG_20170305_103621.jpg) (https://postimg.org/image/lnwzarp67/)
(https://s19.postimg.org/4ne321men/IMG_20170306_181800.jpg) (https://postimg.org/image/4ne321men/)
(https://s19.postimg.org/xd0yyn0of/IMG_20170306_181807.jpg) (https://postimg.org/image/xd0yyn0of/)
(https://s19.postimg.org/6t8dww5e7/IMG_20170306_181813.jpg) (https://postimg.org/image/6t8dww5e7/)
(https://s19.postimg.org/ka5cfv2vz/IMG_20170306_181824.jpg) (https://postimg.org/image/ka5cfv2vz/)
(https://s19.postimg.org/7ir68yg4v/IMG_20170307_171737.jpg) (https://postimg.org/image/7ir68yg4v/)
(https://s19.postimg.org/vmhxxhqyn/IMG_20170307_174817.jpg) (https://postimg.org/image/vmhxxhqyn/)
(https://s19.postimg.org/ka5cfrv5b/IMG_20170307_174837.jpg) (https://postimg.org/image/ka5cfrv5b/)
(https://s19.postimg.org/acubmqxu7/IMG_20170309_182233.jpg) (https://postimg.org/image/acubmqxu7/)
(https://s19.postimg.org/5gqouk59b/IMG_20170309_182253.jpg) (https://postimg.org/image/5gqouk59b/)
(https://s19.postimg.org/40f6cqfan/IMG_20170311_104304.jpg) (https://postimg.org/image/40f6cqfan/)
(https://s19.postimg.org/3oxpzsysv/IMG_20170311_164821.jpg) (https://postimg.org/image/3oxpzsysv/)
(https://s19.postimg.org/suyo71shr/IMG_20170311_164836.jpg) (https://postimg.org/image/suyo71shr/)
(https://s19.postimg.org/kqqk26vr3/IMG_20170311_164853.jpg) (https://postimg.org/image/kqqk26vr3/)
(https://s19.postimg.org/4shuc5gzj/IMG_20170311_164935.jpg) (https://postimg.org/image/4shuc5gzj/)
(https://s19.postimg.org/3q7ntjdkv/IMG_20170311_164952.jpg) (https://postimg.org/image/3q7ntjdkv/)
(https://s19.postimg.org/gvn5z7zm7/IMG_20170312_100407.jpg) (https://postimg.org/image/gvn5z7zm7/)
(https://s19.postimg.org/ykewrd6dr/IMG_20170313_175806.jpg) (https://postimg.org/image/ykewrd6dr/)
(https://s19.postimg.org/dc189gewv/IMG_20170313_175811.jpg) (https://postimg.org/image/dc189gewv/)
(https://s19.postimg.org/x6n9vpc5r/IMG_20170313_175817.jpg) (https://postimg.org/image/x6n9vpc5r/)
(https://s19.postimg.org/k51l5pav3/IMG_20170315_151631.jpg) (https://postimg.org/image/k51l5pav3/)
(https://s19.postimg.org/46svfmtin/IMG_20170315_215615.jpg) (https://postimg.org/image/46svfmtin/)
(https://s19.postimg.org/lk35uibz3/IMG_20170316_153658.jpg) (https://postimg.org/image/lk35uibz3/)
(https://s19.postimg.org/z104ddekv/IMG_20170316_153715.jpg) (https://postimg.org/image/z104ddekv/)
(https://s19.postimg.org/bwznkx8qn/IMG_20170321_183406.jpg) (https://postimg.org/image/bwznkx8qn/)
(https://s19.postimg.org/448zsx06n/IMG_20170321_183429.jpg) (https://postimg.org/image/448zsx06n/)
(https://s19.postimg.org/uf40523cf/IMG_20170321_221104.jpg) (https://postimg.org/image/uf40523cf/)
(https://s19.postimg.org/q5za34d0f/IMG_20170421_122458.jpg) (https://postimg.org/image/q5za34d0f/)
(https://s19.postimg.org/iq00hdugv/IMG_20170421_122505.jpg) (https://postimg.org/image/iq00hdugv/)
(https://s19.postimg.org/6o4mn90nz/IMG_20170421_122516.jpg) (https://postimg.org/image/6o4mn90nz/)
(https://s19.postimg.org/bzjj80k6n/IMG_20170421_122528.jpg) (https://postimg.org/image/bzjj80k6n/)
(https://s19.postimg.org/l7broqee7/IMG_20170421_172134.jpg) (https://postimg.org/image/l7broqee7/)
(https://s19.postimg.org/4wbnsdc67/IMG_20170421_172441.jpg) (https://postimg.org/image/4wbnsdc67/)
(https://s19.postimg.org/fvwv3zxgf/IMG_20170421_183922.jpg) (https://postimg.org/image/fvwv3zxgf/)
(https://s19.postimg.org/5931yjf0f/IMG_20170421_183940.jpg) (https://postimg.org/image/5931yjf0f/)
(https://s19.postimg.org/i1r5y30sf/IMG_20170421_183941.jpg) (https://postimg.org/image/i1r5y30sf/)
(https://s19.postimg.org/3vbf37d67/IMG_20170421_183948.jpg) (https://postimg.org/image/3vbf37d67/)
(https://s19.postimg.org/kj2x5pfnj/IMG_20170421_184013.jpg) (https://postimg.org/image/kj2x5pfnj/)
(https://s19.postimg.org/f7o0l1jb3/IMG_20170421_184338.jpg) (https://postimg.org/image/f7o0l1jb3/)
(https://s19.postimg.org/fylc4a0ov/IMG_20170421_184608.jpg) (https://postimg.org/image/fylc4a0ov/)
(https://s19.postimg.org/3jyk3zjhb/IMG_20170421_184618.jpg) (https://postimg.org/image/3jyk3zjhb/)
(https://s19.postimg.org/ypio0ydnz/IMG_20170422_141455.jpg) (https://postimg.org/image/ypio0ydnz/)
(https://s19.postimg.org/z3oldu50f/IMG_20170422_142048.jpg) (https://postimg.org/image/z3oldu50f/)
(https://s19.postimg.org/e6sd9bjvz/IMG_20170422_142942.jpg) (https://postimg.org/image/e6sd9bjvz/)
(https://s19.postimg.org/i4fmypjjz/IMG_20170422_174848.jpg) (https://postimg.org/image/i4fmypjjz/)
(https://s19.postimg.org/qmp332d7z/IMG_20170426_184017.jpg) (https://postimg.org/image/qmp332d7z/)
(https://s19.postimg.org/n335dc2tb/IMG_20170427_134726.jpg) (https://postimg.org/image/n335dc2tb/)
(https://s19.postimg.org/gcmo3y5dr/IMG_20170429_192756.jpg) (https://postimg.org/image/gcmo3y5dr/)
(https://s19.postimg.org/mdkd10zpr/IMG_20170429_192821.jpg) (https://postimg.org/image/mdkd10zpr/)
(https://s19.postimg.org/7hlttg3qn/IMG_20170502_165824.jpg) (https://postimg.org/image/7hlttg3qn/)
(https://s19.postimg.org/3xzw3ho4f/IMG_20170502_165850.jpg) (https://postimg.org/image/3xzw3ho4f/)
(https://s19.postimg.org/wnms0azvz/IMG_20170518_185708.jpg) (https://postimg.org/image/wnms0azvz/)
(https://s19.postimg.org/z4yj7ome7/IMG_20170530_164852.jpg) (https://postimg.org/image/z4yj7ome7/)
(https://s19.postimg.org/xpwyiwnv3/IMG_20170722_190928.jpg) (https://postimg.org/image/xpwyiwnv3/)
(https://s19.postimg.org/wavdu6f27/IMG_20170725_214253.jpg) (https://postimg.org/image/wavdu6f27/)
(https://s19.postimg.org/db9nz1gwv/IMG_20170728_184604.jpg) (https://postimg.org/image/db9nz1gwv/)
(https://s19.postimg.org/r4y0o26xb/IMG_20170728_184621.jpg) (https://postimg.org/image/r4y0o26xb/)
Jedna strana iskitovana i ofarbana antikorozivnom bojom, kad bude vremena nastavlja se...
(https://s19.postimg.org/u6b0t535r/IMG_20170830_203758.jpg) (https://postimg.org/image/u6b0t535r/)
(https://s19.postimg.org/yffqvbe4v/IMG_20170830_203826.jpg) (https://postimg.org/image/yffqvbe4v/)
-
bravo-iscrpna fotoreportaža :palacgore:
-
Hvala :biggrin:
Bilo je dosta slika, nisam dugo objavljivao, pa je sve nabacano...
-
:mrgreen: :mrgreen: nisi nam se pohvalio da si uzo co2 :mrgreen: :mrgreen:
btw.......nadam se da to sve nisi radio elektro
-
Uh davno sam ga uzeo ima vise od 2 god cini mi se :misli:
Jbg zaboravilo se :mrgreen:
Imace aparat je Varstroj varmig 251 supermig
-
:biggrin: :biggrin: sad se pojavili na netu od firme super goldy inverterski , co2 +inverter i tig .....cijene bolje da ljudi ne cuju jer sam odma kupio inverter 300 A koji vari usudio bi se rec sam :mrgreen: :mrgreen: nisam zdrzl i dva tri dana sam isel po ovaj co2 + inverter pre strasno sta su kinezi poceli poklanjat jer kad znam koliko sam dao za takav inverter prije 10 g :cigle: :cigle:
-
Znaci dobar aparat, nisam mogo vjerovat da moze valjati a da je jeftin, u svakom slucaju ga nekom mogu preporucit sad :biggrin:
-
:mrgreen: :mrgreen: eeeeeee da si njega imal kad si varil auspuf :ja_moren_smoke: :ja_moren_smoke:
-
Tak je kak je jbg :mrgreen: :mrgreen: